The PYXIS RS Cineplate is a cheese plate meticulously designed for the Blackmagic PYXIS 6K right side to fit over the default blackmagic side plate. It enables you to add solid support via an Arri Rosette connector, a 15mm rod for FIZ without any additional accessories, 21 1/4” to holes with locating pins, a 3/8”-16 tapped connector and 4 M4 tapped holes. It also features a reversed countersunk slot to pass through1/4” -20 bolts for attaching to accessories. It also features strategically located recess holes on the reverse side to reduce the weight of the plate.
The 15mm rod features precision-engineered slots that reduce weight without compromising strength, making it ideal for lightweight setups. The integrated slots also offer convenient points for cable management, keeping your rig tidy and organised. Additionally, these slots enhance versatility, allowing you to mount accessories directly to the rod for a streamlined setup.
The PYXIS 6K Transmission Top Bracket was designed to allow you to top mount your Accsoon Cineview Master 4K transmitter to the Blackmagic PYXIS when used with the DJI RS 4,3,2 Pro handheld Gimbal. It overcomes the limitation of mounting it underneath the gimbal which isn’t possible because of the long antennas without it protruding too far out. Mounting onto of the PYXIS also enables more fine tuning of the counterweight balancing needed to get the PYXIS perfectly balanced on the Gimbal set up.
When not used on the Gimbal the PYXIS 6K Transmission Top Bracket can also double as a side-mount option, providing even more flexibility for your rig configuration.
The Simple LiDAR Bracket for the DJI LiDAR unit and DJI RS Focus Pro allows users to mount the LiDAR in multiple configurations, including closer to the axis of the taking lens, under a matte box, or other positions made possible by its adjustable arm with a 1/4”-20 thread.
At just 9g, it is the lightest commercially available LiDAR mounting solution, significantly lighter than DJI’s original 25g bracket. This weight reduction moderately reduces the counterweight required, making balancing easier and more efficient.
It is compatible with both the current and previous LiDAR units.
PLATE
Weight (g) 205
Diameter (mm) 140 x Width 84.58 xHeight 34.17
ROD
Weight (g) 18
Diameter (mm) 14.95 x Width N/A xHeight 100
TRANSMITTER BRACKET
Weight (g) 23
Diameter (mm) 86 x Width 20 x Height 32
Material: AL6061-T6
Finish: Sandblasted + anodised
SIMPLE LiDAR BRACKET
Weight (g) 9
Diameter (mm) 58.52 x Width 29.08 x Height 4
Material: AL6061-T6
Finish: Sandblasted + anodised
The PYXIS RS Cineplate is a cheese plate meticulously designed for the Blackmagic PYXIS 6K right side to fit over the default blackmagic side plate. It enables you to add solid support via an Arri Rosette connector, a 15mm rod for FIZ without any additional accessories, 21 1/4” to holes with locating pins, a 3/8”-16 tapped connector and 4 M4 tapped holes. It also features a reversed countersunk slot to pass through1/4” -20 bolts for attaching to accessories. It also features strategically located recess holes on the reverse side to reduce the weight of the plate.
The 15mm rod features precision-engineered slots that reduce weight without compromising strength, making it ideal for lightweight setups. The integrated slots also offer convenient points for cable management, keeping your rig tidy and organised. Additionally, these slots enhance versatility, allowing you to mount accessories directly to the rod for a streamlined setup.
The PYXIS 6K Transmission Top Bracket was designed to allow you to top mount your Accsoon Cineview Master 4K transmitter to the Blackmagic PYXIS when used with the DJI RS 4,3,2 Pro handheld Gimbal. It overcomes the limitation of mounting it underneath the gimbal which isn’t possible because of the long antennas without it protruding too far out. Mounting onto of the PYXIS also enables more fine tuning of the counterweight balancing needed to get the PYXIS perfectly balanced on the Gimbal set up.
When not used on the Gimbal the PYXIS 6K Transmission Top Bracket can also double as a side-mount option, providing even more flexibility for your rig configuration.
The Simple LiDAR Bracket for the DJI LiDAR unit and DJI RS Focus Pro allows users to mount the LiDAR in multiple configurations, including closer to the axis of the taking lens, under a matte box, or other positions made possible by its adjustable arm with a 1/4”-20 thread.
At just 9g, it is the lightest commercially available LiDAR mounting solution, significantly lighter than DJI’s original 25g bracket. This weight reduction moderately reduces the counterweight required, making balancing easier and more efficient.
It is compatible with both the current and previous LiDAR units.
PLATE
Weight (g) 205
Diameter (mm) 140 x Width 84.58 xHeight 34.17
ROD
Weight (g) 18
Diameter (mm) 14.95 x Width N/A xHeight 100
TRANSMITTER BRACKET
Weight (g) 23
Diameter (mm) 86 x Width 20 x Height 32
Material: AL6061-T6
Finish: Sandblasted + anodised
SIMPLE LiDAR BRACKET
Weight (g) 9
Diameter (mm) 58.52 x Width 29.08 x Height 4
Material: AL6061-T6
Finish: Sandblasted + anodised
